|
Product Details:
Payment & Shipping Terms:
|
| Standard: | IEC60601 | Material: | Delrin And Stainless Steel |
|---|---|---|---|
| Type: | Accessability Probe | Conditon: | New |
| Shipment: | By Express | Warranty: | 1 Year |
| Highlight: | finger probe test,ul test finger |
||
IEC60601 Test Probe Kit Includes Test Hook Standard Test Finger Unjointed Finger Probe etc.
The PG-60601 contains the device listed in the core of the UL / IEC / EN 60601 requirements. It includes the following probes:
1. Jointed Finger Probe
| Diameter of finger: | 12mm | Length of finger: | 80mm |
| Diameter of baffle: | 50mm | Length of baffle: | 100mm |
| Thruster (optional) | 10N | ||
| Material: Insulating material (baffle and handle), stainless steel(finger) | |||
2. 50mm Impact Test Ball
2.1 Impact steel ball: Φ50mm, 500±25g
3. Short Test Pin Probe
3.1 Introduction:
The Short Test Pin Probe (conical short taper test pin : Φ3~4-length 15) is designed according to IEC61032 figure 9. The pin is intended to verify the protection against access to hazardous live parts in class 0 equipment and class II equipment (see IEC60536)
3. 2.Specification:
| diameter of test pin | head 3mm, bottom 4mm |
| length of test pin | 15mm |
| diameter of baffle | 25mm |
| thickness of baffle | 4mm |
| material | insulating material, metal |
4. Rigid Finger Probe
4.1 Introduction:
Rigid Finger Probe (unjointed test finger) is designed according to IEC61032 figure 7 and UL clauses. This probe may be used to verify the protection of persons against access to hazardous parts, and to verify the mechanical strength of openings in the enclosure or internal barriers. 50N force recommend to be applied.
4.2 Specification:
| diameter of test finger | 12mm |
| Length of test finger | 80mm |
| Diameter of baffle | 50mm |
| Thickness of baffle: | 5mm |
| Strength range | 10N, 20N, 30N, 40N, 50N |
| Material | insulating material, metal |
5. Ball Pressure Tester
The ball pressure tester is designed according to IEC60695-10-2, IEC60335, IEC60601, GB4706.1 and etc. the surface of the part to be tested is placed in the horizontal position and a steel ball of 5 mm diameter is pressed against the surface with a force of 20 N. The test is performed in a heating cabinet at a temperature of 75°C ± 2°C. The ball is withdrawn after 1 h and the diameter of the impression made by the ball is measured. An impression greater than 2 mm in diameter constitutes a failure.
5.1 Parameters
| Ball diameter | 5mm (R2.5mm) |
| Test Pressure | 20N±0.2N |
| Material | Stainless Steel |
| Sample supportor | Φ50mm-length 100mm, cylinder sharp |
6. Test Hook
6.1 Introduction
The test hook is designed according to IEC60065:2005 and GB8898-2009 figure 4. It is mainly applied to do the protection test against electric shock, it is a necessary tool for QC department.
6. 2 Specification
● Length: 180mm
● Width: 8mm
● Length of hook: 5mm
● Thickness: 1mm
7. 4.0mm Hazardous Live Parts Probe
The IEC60601 Test Probes are packed in a custom-cut foam padded silver case and can be required with the ISO17025 accredited certificates of calibration -- with specific scope for “Accessibility Probes”. And it meets requirements for testing standards including but not limited to CAS601, IEC60601, UL2601 and EN60601.
Contact Person: Ms. Penny Peng
Tel: +86-18979554054
Fax: 86--4008266163-29929
